Quick question about Pragraphix LED tape

Ask and answer questions, share tips and resources for installing lighting and other electronics in your models.

Moderators: Sparky, Moderators

Post Reply
User avatar
TurkeyVolumeGuessingMan
Posts: 3367
Joined: Fri Aug 10, 2012 6:31 pm
Location: Gunma-ken, Japan
Contact:

Quick question about Pragraphix LED tape

Post by TurkeyVolumeGuessingMan »

So I bought some of this great LED tape from Cult TV Man at the WonderFest last summer. It says that there's no need to be concerned about calculating resistors. But shouldn't the number of LEDs affect how the light shines? I would think that the length of the tape and how many LEDs are lit would affect the necessary resistance. How does this work, anyway?
Greg
Plastic modeling and other nerd stuff in Japan on my YouTube channel
My WIP modeling page on Tumblr.
One day I was walking and I found this big log. Then I rolled the log over and underneath was a tiny little stick. And I was like, "That log had a child!"
User avatar
Mr. Engineer
Posts: 440
Joined: Mon Dec 10, 2007 6:01 am
Location: Malaysia
Contact:

Post by Mr. Engineer »

The Paragrafix LED strip uses 12 volts, can be cut at every 2-inches and has current-limiting resistors built into it.

Based on this fact, each LED cluster (of three LEDs) would be connected serially and has ONE resistor per cluster. You can then control the brightness by adjusting the input DC voltage from 6 to 12.

Or alternatively, use PWM circuits to fast flicker the LEDs thus fooling your eyes (Persistent of Vision) that they're constantly ON but in reality, is not.

[Edit]
The longer the LED strip is, the more powerful your power supply will need to be in terms of pumping more current.
What can I take apart today?

https://www.facebook.com/PisceanWorks
User avatar
TurkeyVolumeGuessingMan
Posts: 3367
Joined: Fri Aug 10, 2012 6:31 pm
Location: Gunma-ken, Japan
Contact:

Post by TurkeyVolumeGuessingMan »

Mr. Engineer wrote:The longer the LED strip is, the more powerful your power supply will need to be in terms of pumping more current.
OK, thanks. That's what I needed to know. I am working on lighting up ships from the old MPC Hoth Rebel hangar diorama. I've done the Rebel Transport with regular blue LEDs (I've shared this in another thread on here). What I am wanting to do next is use a section of the LED tape from Paragraphix to light up the Millenium Falcon. I will only use a small 3 LED segment.

Eventually when I build my 1:144 Fine Molds Falcon, two segments of LED tape (6 lights) will fit perfectly for the rear thrusters.
Greg
Plastic modeling and other nerd stuff in Japan on my YouTube channel
My WIP modeling page on Tumblr.
One day I was walking and I found this big log. Then I rolled the log over and underneath was a tiny little stick. And I was like, "That log had a child!"
User avatar
Mr. Engineer
Posts: 440
Joined: Mon Dec 10, 2007 6:01 am
Location: Malaysia
Contact:

Post by Mr. Engineer »

No problem, Greg.

You'll only need more current when the strip is more than a few metres long. I've been playing with the 1/144 Milllenium Falcon two years ago and have almost completed designing the circuit board for it. But I did not have the chance to get the shops to prototype the board for me due to my (current) Job away from home. But in all, the LEDs were designed for parallel lighting since I love to work in low voltages. Higher voltage means brighter LEDs and all but this also generates heat which worries me when it comes to scale modeling.

Using the LED's hotspot properties, I can get away with about a few LEDs to make a consistent bar of light but I cannot remember the exact number as the model was very small and so long ago.

I understand what you're trying to do, which is called (in my own terms) Scale Lighting. Understanding what each LED can do and work with its characteristics/flaw is quite interesting!
What can I take apart today?

https://www.facebook.com/PisceanWorks
User avatar
TurkeyVolumeGuessingMan
Posts: 3367
Joined: Fri Aug 10, 2012 6:31 pm
Location: Gunma-ken, Japan
Contact:

Post by TurkeyVolumeGuessingMan »

I've got another question: these Paragraphix LED Tape connectors are compatible with any LED tape, right? It's all the same, I hope.

This project of mine will incorporate straight 3mm LEDs, LED tape, and fiber optics. I plan to use fiber optics with a red LED to light the engines of the tiny X-Wings.
Greg
Plastic modeling and other nerd stuff in Japan on my YouTube channel
My WIP modeling page on Tumblr.
One day I was walking and I found this big log. Then I rolled the log over and underneath was a tiny little stick. And I was like, "That log had a child!"
User avatar
veedubb67
Posts: 872
Joined: Tue Aug 16, 2005 11:12 pm
Location: Colorado Springs, CO
Contact:

Post by veedubb67 »

Yes, they should work just fine since there's only 2 connections (positive and negative).

I've used Paul's LED tape on several of my builds and have had good success running them on 9V.


Rob
Iwata Padawan
User avatar
TurkeyVolumeGuessingMan
Posts: 3367
Joined: Fri Aug 10, 2012 6:31 pm
Location: Gunma-ken, Japan
Contact:

Post by TurkeyVolumeGuessingMan »

Thanks. I wasn't sure if LED tape came in different widths. I have a lot of those connectors, but it turns out that I won't be able to use one for my first model kit using the tape. I'll have to solder the wires to the contact points. Badgrendels has a tutorial video on how to do this on YouTube.
Greg
Plastic modeling and other nerd stuff in Japan on my YouTube channel
My WIP modeling page on Tumblr.
One day I was walking and I found this big log. Then I rolled the log over and underneath was a tiny little stick. And I was like, "That log had a child!"
User avatar
Mr. Engineer
Posts: 440
Joined: Mon Dec 10, 2007 6:01 am
Location: Malaysia
Contact:

Post by Mr. Engineer »

If I am not mistaken, these LED strips comes in 10mm to 12mm widths and the really thin ones (like a stick) would be about 2.5mm wide.
What can I take apart today?

https://www.facebook.com/PisceanWorks
User avatar
brt
Posts: 1932
Joined: Thu Feb 14, 2008 6:04 pm
Location: Waiting for the Mothership

Post by brt »

“Life is pain, highness. Anyone who says differently is selling something.”
― William Goldman
Post Reply